矿用直线振动筛结构故障分析

针对煤矿选煤厂直线振动筛工作过程中出现的结构故障问题,采用有限元仿真与现场测试结合的方法对振动筛出现故障的原因进行了分析研究。介绍了振动筛的主要结构及常见故障,并以某矿选煤厂发生大梁断裂的振动筛为例,对该振动筛进行三维建模和有限元模态分析,分析结果表明:随着模态阶次的增加,振型的变化逐渐由移动转为结构本身的扭曲变形。在该振动筛空载工作状态下,选用本质安全型便携式测振记录仪进行振动测试并处理测试信号,得到该振动筛的工作频率。结合模态分析结果和实际测试结果,判断出空载时频繁运行振动筛是造成其大梁断裂的主要原因。根据故障原因给出维护建议:应当尽量避免振动筛在空载或物料较少的状态下长时间运行;在振动筛投入使用前,应预先了解振动筛的工作状态及可能存在的薄弱环节,尽可能避免结构故障,保证振动筛可靠运行。     

Free vibration behavior of a thermally post-buckled FG Timoshenko beam under large deflection using a tangent stiffness-based method

For thermally postbuckled configurations, the free vibration behavior of functionally graded (FG) Timoshenko beams are investigated. The postbuckling configurations are obtained through a geometrically nonlinear static problem. The free vibration problem around the postbuckled configuration is formulated using its tangent stiffness. The energy based governing equations are solved following the Ritz method. The elements of the tangent stiffness matrix are obtained using the Ritz coefficients. The results are shown to exhibit the effects of FG material, material profile parameter, and length-thickness ratio. The comparative results are presented for both the cases of the physical neutral surface and the geometrical neutral surface.     

双光束激光焊匙孔动态特征分析

文中研究了高功率单光束激光焊与双光束激光焊过程中匙孔动态特征的差别. 结果表明，单光束激光焊及双光束激光焊接过程中匙孔均处于从产生到湮灭的剧烈波动的过程，不同于单光束激光焊匙孔的形成、长大、维持、缩小、湮灭过程，双光束激光焊的匙孔还存在分离长大及合并缩小的过程；在相同的焊接参数及焊缝具有相同熔深的条件下，双光束激光焊匙孔的波动频率约为单光束激光焊的2/3，单光束激光焊匙孔的开口面积均值约为双光束激光焊匙孔开口面积的1/2，开口面积的波动变异系数约为单光束激光的2倍，即双光束激光焊过程中匙孔较单光束激光焊的具有较高稳定性.     

用宽带超表面产生阵列贝塞尔光束

通过在空间光调制器（SLM）上加载相位图或通过光刻加工微型圆锥状结构可以产生贝塞尔光束阵列。然而，典型空间光调制器具有比波长大一个数量级的像素尺寸，这限制了相位梯度的可用范围，用光刻法加工的微型锥透镜的顶端不是标准的圆锥，这影响了贝塞尔光束的质量。为了克服这些缺点，将复杂的相位图加载到电介质超表面上，设计了一种可以产生阵列贝塞尔光束（在波长700 nm处，NA=0.3）的超表面器件。该器件可以宽波段工作，其单元结构在波长580~800 nm范围内的偏振转换效率均超过57%。利用时域有限差分算法（FDTD）对该器件（厚度为380 nm，直径仅为40 μm）进行了仿真，所产生的阵列光束都垂直于超表面器件。所提出的阵列贝塞尔光束发生器具有纳米级别的厚度和几十微米的直径，这对于未来的集成光学领域具有很大的应用前景。     

海水淡化用空心锥喷嘴喷淋性能理论及实验研究

设计开发一种具有高通量、低流阻特征的空心锥喷嘴,并通过理论与实验方法研究空心锥喷嘴的喷淋性能,基于准自由涡理论建立空心锥喷嘴内部流体流动的数学模型,阐明流量系数、喷淋锥角、喷嘴流量与喷嘴结构参数之间的定量关系,并利用多效蒸馏海水淡化喷淋实验台对理论计算结果进行实验测试和验证。研究结果表明:正常工作状态下喷嘴流量系数、喷淋锥角、喷淋流量等参数理论值与测量值之间的误差小于5%,验证了设计模型的准确性。同时根据实验测试数据,拟合得到该类型空心锥喷嘴喷淋锥角与雷诺数之间的经验公式,可为蒸馏海水淡化用大流量空心锥喷嘴的结构设计、工艺选型提供理论指导和数据支持。     

Focusing characteristics of the relativistic electron beam transmitting in ion channel

Based on the beam–plasma system model established in this paper, the trajectory of the electron beam in the ion channel is studied quantitatively through the envelope equation. Under different initial system parameters, the focusing transmission conditions of the beam in the ion channel are discussed. Then, a series of particle-in-cell simulations are performed, which generally versifies the theoretical results and shows some further details of the focusing behavior of the beam. It is found that the deceleration of some electrons around the focusing point or the beam–plasma interaction at the ion channel boundary will result in the generation of the residual electrons,which forms the electron return current that leads to the new instabilities influencing the focusing characteristics of the beam.     

The Impingement Heat Transfer Data of Inclined Jet in Cooling Applications: A Review

On the impingement heat transfer data,the experimental studies of air and liquid jets impingement to the flat surfaces were collected and critically reviewed.The oblique impingements of both single circular and planar slot jets were considered in particular.The review focused on the surface where the jet impingement cooling technique was utilized.The nozzle exit Reynolds numbers based on the hydraulic diameter varied in the range of 1,500–52,000.The oblique angles relative to the plane surface and the dimensionless jet-to-plate spacing vary in the range of 15°–90°and 2–12 respectively.The review suggested that the magnitude of maximum heat transfer shifted more for air jets compared with the liquid jets.The drop in the inclination angle and the jet-to-plate separation led to the increase in the asymmetry of heat transfer distribution.The displacement of maximum Nusselt number(heat transfer)locations was found to be sensitive to the inclination angle and the smaller jet-to-plate distance.Also,the Nusselt number correlations proposed by various researchers were discussed and compared with the results of the cited references.     

Fabrication of highly sensitive MnO2/F-MWCNT/Ta hybrid nanocomposite sensor with different MnO2 overlayer thickness for H2O2 detection

In this work, we report the development of MnO₂/F-MWCNT/Ta hybrid nanocomposite sensor with different MnO₂ overlayer thickness for the detection of H₂O₂ in real samples. A novel two-step process using e-beam evaporation and spray pyrolysis deposition was adopted for the synthesis of hybrid MnO₂/F-MWCNT/Ta electrodes. SE morphology revealed smaller-sized, compact grains of MnO₂ infiltrated on the outermost walls of MWCNTs. Raman analysis confirmed the existence of carbon nanotubes with abundant structural defects of MnO₂ in the composite. The cyclic voltammetry results displayed a high peak current and narrowed over potential towards the reduction of H₂O₂. The sensor displayed a fast response (<5?s), wide linear range (2–1510?μM) and a low limit of detection (0.04?μM) with significant anti-interfering properties, promising for the development of highly sensitive and reproducible biosensors. The three dimensional nanocomposite sensor also exhibited good recovery (> 98%), thus providing a favourable tool for analysis of H₂O₂ in milk samples.     

加工切割精度对研磨的影响

本文主要介绍了在加工基板边部时,需将控制边部质量放在首。对于边部质量控制的重要环节是切割工序,切割的精度将直接影响到研磨边部的质量,从而影响边部良品率。因此,切割精度是作为控制边部质量的第一要素。     

基于BEPCⅡ数字束流位置测量系统电子学系统的设计与实现

BEPCⅡ加速器的束流位置测量系统（BPM）模拟电子学经过十余年的运行逐渐老化，故障率上升，亟需进行升级改造。本文根据该需求，自行设计了基于BEPCⅡ系统参数的数字BPM电子学系统，内容包括模拟信号处理电子学、数字信号处理电子学、BPM固件算法逻辑、数据获取软件以及系统测试等多个部分。设计的数字BPM电子学系统经实验板级性能测试、实验室系统测试以及在线束流测试，结果表明该系统能满足BEPCⅡ装置对束流位置测量的需求。